How to Install Baseboard Moulding with Profile Mryoucandoityourself

Just a few words about how to install baseboard moulding with profile. Installing baseboard moulding with profile I faced with some difficulties to install them on the corner of the walls. Only after several baseboard molding installation I got some skills how to do it fast. In this project I made 22.5 and 45 degree angle cuts on the material. You can watch one more video about how to cut basebpard moulding fast here:
Just watch the video “How to Install Baseboard Moulding with Profile” and you’ll understand everything you need to know. If you have any questions, I am here to help you with your baseboards installation for hardwood, laminate and floating floor installation.
– Dewalt Miter Saw –
– Pin Nailer 23-Gauge –
– Compressor –
– Compressor hose –

Canon T5i –

Favorite tools:
– Dewalt Table Saw –
– Milescraft FeatherBoard –
– Router Table –
– Dewalt Miter Saw Crown Stops –
– Dewalt 18 Ga nail gun –
– Dewalt 16 Ga nail gun –
– Dewalt circular saw –
– Festool 36 Auto Clean Vacuum –
– Makita Jig Saw –
– Makita Cordless Tool Kit –
– Laminate cutter –
– Rubber Mallet –
– Rockwell Versacut Saw –
– Fein Multimaster –
– Undercut Saw –
– Angle Grinder –
– Sliding T-Bevel –
– Hot Glue Gun –
– Adhesive Gun –
– Construction Adhesive –
– Wood Glue –
– Tongue and Groove Glue –
– Heavy-Duty Utility Knife –
– Duct Tape –
– Scotch Masking Tape –
– Clamp –
– Water Based Spray –
– Bostik Best flooring glue –

Click this link for my other Hardwood Flooring Tutorials!

Click this link for my other Laminate Flooring Tutorials!

Click this link for my other Laminate Stairs Tutorials!

Click this link for my other Hardwood Stairs Tutorials!

Click this link for my other subfloor leveling tutorials

Thanks for watching!

Let me know what you think by commenting and rating this video!
Don’t forget to subscribe 🙂

Main Channel:

How to Install Baseboard Moulding with Profile


German Rojas says:

Shoot more nails in tht shit it my fall in couple days

e Rob says:

you do great work, I would like to see a video about cutting baseboards around the outside of a bullnose corner. how do you get the measurements etc.

gringo90100 says:

Do u put posts of Nails. Or you just slide the gun. In bace board?

MrYoucandoityourself says:

Excuse me, can you write your comment/question in English, please?

Jeffrey Rosenzweig says:

Does the pin nailer hold well? I have the Ryobi 15ga finish nailer and was planning to use that for MDF baseboards. Do you think it’s too big of a nail?

Matthew Smith says:

The corners where a nice touch.

MrYoucandoityourself says:

Thank you for watching this video. The size is 1 1/4″ (one and quarter inch).

wolfplex1 says:

Very nice floors!!!!

Chi-town57 says:

What did you use to make the opening and closing title screens where the hand is writing on the paper? I’ve seen that on a few other channel’s videos

Demitri Baskin says:

Always glue the joints, those will open in one season…

MrYoucandoityourself says:

Thank you so much!

PAYONG Sejtura says:


Venom101002 says:

If you are going to go install moulding, after watching this video, I wish you luck. It tells you nothing.

lukejo45 says:

It would help if u had some commentary this video is of no use

lou jones says:

Is this supposed to be an instructional video or just a video of you showing off?

 Write a comment


Do you like our videos?
Do you want to see more like that?

Please click below to support us on Facebook!