Bathroom ceiling cladding

How to clad a bathroom ceiling using PVC cladding. Brought to you by http://www.ultimatehandyman.co.uk/forum1/

Comments

John Hope says:

Hi I want to clad the ceiling and walls of my ensuite. What grap adhesive would you recommend?

Garry Gemmell says:

How did you seal the edges – silicone sealant or more likely some form of edge strip like a tiling edge strip?
Plan do do my bathroom as the previous resident fitted wood without putting zinser on knots – looks terrible.
Impossible to sand down or nitromors without a lot of hassle and mess so planning on putting up that plastic cladding – looks nice with the silver in between not seen that one before – Wickes?

fireblade19746 says:

Great short film, will have ago myself. Bathroom needs doing thanks

Riyaj Bagewadi says:

I will be tray

Garry Gemmell says:

Is it just me or does vid crash at 12 mins!

Ossama Zd says:

how can i make a movable pvc

Jon Lennon says:

do you recommend cutting out the holes for the led downlighters first in the ceiling,then as you put up the cladding section piece where the downlighter will go then cut the hole obviously ground level how you showed video or temporary put up cladding section dril hole through cladding and artex ceiling so yiu hace a centre hole to work from…cheers

alhoggy77 says:

Hi

I have wooden panels with brass down lights – want to replace with pvc cladding panels & chrome lights , what’s the easiest option for replacement & cuttng out, was thinking simply removing original panels & using as template for length & cutting out holes for lights ? Would this be best option ? Panels are the same size !!!

Cheers

Alan

Kamala Mammadli says:

is this material safe ? It is said to be highly flammable .Any opinions?

Jon Lennon says:

hi I could not find led down lighters you fitted eBay just ones with white tubes mounting any help appreciated

Bilal DZ says:

Good job man.. Well done! I like it.

EWI & Facade Products says:

What a great video!

sam737373 says:

are you not supposed to use click in coving for the edges

Jon Lennon says:

hi I could not find led down lighters you fitted eBay just ones with white tubes mounting any help appreciated

Phil Richmond says:

Great job handyman. What size batons did you use?

Vijay Rajput says:

Can i put this over existing cladding

Jo A says:

So I wouldn’t be able to do this with just a normal ceiling light, I’d have to get led lights?

Jon Lennon says:

thankyou……

brucedickinson12 says:

where can i buy this cladding please

Andy O says:

Can you advise me please, plastered two new walls in a bathroom before fitting splash panel to these. What do I need to do to the new plaster before splash panel is fitted. Is a simple watered down coat of emulsion suffice?
Thank you

Jon Lennon says:

thanks for the advice much appreciated…keep up excellent videos I have learnt so much.

Jacky Wong says:

good work

Little Miss Maddie says:

you never showed how you cut your holes

James Jospeh Nicoll says:

Those screws are a pain in the arse. Especially working above your head. Seen a tip on YouTube to hold the screws using a rare earth magnet on screwdriver bit. Made it a lot easier

Jon Lennon says:

hi I could not find led down lighters you fitted eBay just ones with white tubes mounting any help appreciated

Jon Lennon says:

hi I could not find the led down lighters you fitted eBay just ones with white cylinder cones tubes on any help where you got them from cheers

Jon Lennon says:

hi I could not find the led down lighters you fitted eBay just ones with white cylinder cones tubes on any help where you got them from cheers

Jon Lennon says:

hi I could not find led down lighters you fitted eBay just ones with white tubes mounting any help appreciated

Josh Nielson says:

Hi, you left a little gap for expansion at the edges right? What would you fill this with? silicone?…. I am renewing the plasterboard ceiling in my bathroom (which is under a flatroof extension) in a couple of months as I need to access the wiring for a few different things and think I may go down the cladding route instead of replacing the plasterboard.

Jon Lennon says:

great video as usual thanks,where did you get ceiling cladding from and led downlighters from 9watt do they come with transformer or not….thanks…jon

MR DIY says:

how do you finishing the edgeing off

mark hesselgreaves says:

Tried to fit ceiling cladding today; got three boards up; and they all fell down soon after. I put silicone behind it, and used staples along the edge to help hold it up while the stuff was setting; it all fell down I cant paint the ceiling because i tried recently and the paint all bubbled and fell off in big slakes like molten rubber face mask, went everywhere, and it took over three hours to remove the stuff from the kitchen cupboards, worktops and the floor. I thought that cladding would be the answer, only to find that, THAT wont stay up either!. Think I’ll just graffiti it with spray paint! make a feature of it; any spray painters, graffiti artists out there?
I’m not interested in fitting a false ceiling, as its too costly, and i’d probably screw that up too. Over the years, this ceiling has had all kinds of repairs done so there are a few coats of plaster on it, in many layers, so i cant even peel it. Tried skimming it; when I started painting it, the plaster came off onto the roller. Maybe i should just do the tried and tested method, and bolt the stuff up! I was told to use silicone, but it doesn’t work; gonna use heavy duty grab adhesive; or, i would if i was confident it wouldn’t fail too. Ahh; i give up.

John Morris says:

Thank You for making these videos, really appreciate them.

Ronin Blax Mushroom Cloud says:

Gerard Butler.

David Conway says:

Brill tutorial as usual. Where does your extractor go? and what kit did you use.

sam737373 says:

did you just cover the access hatch .

Jon Lennon says:

hi I could not find led down lighters you fitted eBay just ones with white tubes mounting any help appreciated

Andy O says:

Someone stealing your videos……. https://www.youtube.com/watch?v=Gb5UTyEFX3Q

Colin Dempsey says:

Nice presentation. One question: If this is a kind of tongue & groove and you are screwing through the tongue, I’d expect the screw to interfere with the matching groove. Where am I misunderstanding?

Jon Lennon says:

hi I could not find led down lighters you fitted eBay just ones with white tubes mounting any help appreciated

JOGO says:

Fantastic !

Brandon C says:

great tutorial man

Jon Lennon says:

thanks for the quick reply back re led downlighters from screwfix,i noticed they are ip20 rated only,as they are going in bathroom with a shower assumed should be ip65 rated…..thanks…jon

Andy Orton - Southpaw guitar UK says:

I’m trying this on porch ceiling, using j trim edging

paddymanz says:

How can plastic expand

 Write a comment

*

Do you like our videos?
Do you want to see more like that?

Please click below to support us on Facebook!